{"product_id":"peplink-acw-634-10ft-dc-power-cable-ignition-sense","title":"Peplink 10ft DC Power Cable – 4-Pin to Direct Wire with Ignition Sense (ACW-634)","description":"\u003cp\u003eHardwire your Peplink or Pepwave router straight into a vehicle or equipment DC power system with the \u003cstrong\u003ePeplink ACW-634 10ft DC Power Cable\u003c\/strong\u003e. One end has the 4-pin Molex Micro-Fit connector used on Peplink mobile routers; the other end is bare, direct-wire leads ready for your fuse block, battery or power distribution panel. It is the Peplink-recommended way to permanently install a router in a vehicle and to use \u003cstrong\u003eignition sensing\u003c\/strong\u003e.\u003c\/p\u003e\u003ch3\u003eIgnition Sense: Router Power That Follows the Key\u003c\/h3\u003e\u003cp\u003eThe 4-pin connector carries more than just power. Along with the positive and ground leads, it has a dedicated \u003cstrong\u003eignition input (IGN)\u003c\/strong\u003e lead and an \u003cstrong\u003eI\/O (GPIO)\u003c\/strong\u003e lead. Wire the IGN lead to an ignition-switched (accessory) circuit and the router knows when the engine is on or off.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eKey on:\u003c\/strong\u003e the router powers up and connects automatically. No buttons to press.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eKey off:\u003c\/strong\u003e the router stays online for a delay you choose, then shuts down cleanly so it never drains the battery.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShort stops covered:\u003c\/strong\u003e fueling, deliveries and quick stops don't drop the connection, because the router waits out the delay before powering down.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eIgnition sensing is turned on in the router's web admin under \u003cem\u003eAdvanced \u0026gt; Misc. Settings \u0026gt; GPIO\u003c\/em\u003e. If you don't need it, simply leave the IGN lead insulated and unconnected.\u003c\/p\u003e\u003ch3\u003e12V to 52V DC Wiring\u003c\/h3\u003e\u003cp\u003eThe ACW-634 is built for hardwired DC installs across \u003cstrong\u003e12V to 52V DC\u003c\/strong\u003e systems, covering cars, vans and pickups (12V), trucks, buses and heavy equipment (24V), and 48V marine, solar, telecom and battery-bank systems.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eImportant: the safe input voltage depends on your router model.\u003c\/strong\u003e For example, the BR1 Pro 5G accepts 10V–30V DC, while the Transit Duo Pro accepts 12V–56V DC. Please check your router's DC input rating before connecting, or reach out to Crosstalk Mobile if you're unsure.\u003c\/p\u003e\u003col\u003e\n\u003cli\u003e\n\u003cstrong\u003ePositive (+):\u003c\/strong\u003e connect to a constant (always-on) fused positive source.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGround (–):\u003c\/strong\u003e connect to chassis ground or the negative bus bar.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIgnition (IGN):\u003c\/strong\u003e connect to a fused, ignition-switched circuit. Leave unconnected if not used.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eI\/O (GPIO):\u003c\/strong\u003e optional; leave insulated unless you use the router's GPIO features.\u003c\/li\u003e\n\u003c\/ol\u003e\u003cp\u003e\u003cstrong\u003eInstall tips:\u003c\/strong\u003e add an inline fuse close to the power source, match each lead to the pin labels in your router's hardware guide, and secure the cable away from heat and moving parts. For fleet or commercial installs, Crosstalk Mobile can help plan the wiring.\u003c\/p\u003e\u003ch3\u003eCompatible Peplink Routers\u003c\/h3\u003e\u003cp\u003eBR1 Classic (HW3), BR1 Mini, BR1 Mini Core, BR1 Mini 5G, BR1 Mini 5G (Wi-Fi), BR1 Mini M2M, BR1 Pro (CAT-20), BR1 Pro 5G, BR2 Pro, BR2 Micro, BR2, Transit Mini, Transit Core, Transit Duo Pro, Transit Pro E, B One, B One Plus, B One 5G and MAX Adapter.\u003c\/p\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eDo I have to connect the ignition (IGN) wire?\u003c\/strong\u003e\u003cbr\u003eNo. If you don't need ignition sensing, leave the IGN lead insulated and unconnected and the router will run whenever power is applied.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan I use this on a 24V truck or 48V system?\u003c\/strong\u003e\u003cbr\u003eThe cable can be used across 12V–52V DC systems, but your router must also support that voltage. Check your router's DC input rating, or contact us and we'll confirm before you wire it.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDo I need a fuse?\u003c\/strong\u003e\u003cbr\u003eYes. The cable has no built-in fuse, so install an inline fuse close to the power source, sized to your router's power requirements.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhich routers does it fit?\u003c\/strong\u003e\u003cbr\u003eAny Peplink router with the 4-pin Molex Micro-Fit power port, including the BR1 Mini, BR1 Pro 5G, BR2 Pro, Transit and B One series listed above.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePart number: ACW-634\u003c\/li\u003e\n\u003cli\u003eRouter end: 4-pin Molex Micro-Fit connector\u003c\/li\u003e\n\u003cli\u003eSource end: direct-wire bare leads\u003c\/li\u003e\n\u003cli\u003eLength: 10 ft \/ 3 m\u003c\/li\u003e\n\u003cli\u003eDC systems: 12V–52V DC (safe voltage depends on router model)\u003c\/li\u003e\n\u003cli\u003eSupports: ignition sensing and GPIO on compatible routers\u003c\/li\u003e\n\u003cli\u003eBrand: Peplink (genuine accessory)\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Peplink","offers":[{"title":"Default Title","offer_id":67787073912922,"sku":"ACW-634","price":19.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0731\/9237\/4362\/files\/acw-634.png?v=1792518355","url":"https:\/\/crosstalkmobile.com\/products\/peplink-acw-634-10ft-dc-power-cable-ignition-sense","provider":"Crosstalk Mobile","version":"1.0","type":"link"}